Poleline Hardware

Anchor Rods

Strand Eye (Stainless Steel Type 316)
Rolled threads are furnished on all rods up to and including 3/4″ diameter. One inch and larger threads. Length of threads 3 1/2″. Manufactured to ANSI standards. All eyes shown to be furnished with one square nut.

Please Note:
EYE RODS / EYE BOLTS: Eye Bolts and Anchor Rods will not look exactly like catalog drawings. Generally all eyes will be investment cast or forged tear drop oval eye or thimble eye shaped nuts attached to double end stud or rod and be a little larger than the minimum inside diameter stated in some catalogs. The eye opening widths for oval eyes work well and will accommodate most all suspension hanger bolt sizes.

All anchor rods fabricated with double ended studs and eye nuts.
(Single, Double, or Triple eye)

06-Poleline-Hardware-image-01

Single Eye

Catalog Number

Rod Diameter

Minimum Strength (Lbs.)

Length (Ft.)

Approximate Weight

(Lbs. per 100 pieces)

Detail

AR1-126316

1/2

10,000

6

450

A

AR1-586316

5/8

16,000

6

664

A

AR1-588316

5/8

16,000

8

830

A

AR1-348316

3/4

23,000

8

1,245

A

Double Eye

Catalog Number

Rod Diameter

Minimum Strength (Lbs.)

Length (Ft.)

Approximate Weight

(Lbs. per 100 pieces)

Detail

AR2-2586316

5/8

16,000

6

690

B

AR2-588316

5/8

16,000

8

840

B

AR2-346316

3/4

23,000

6

970

B

AR2-348316

3/4

23,000

8

1403

B

AR2-341316

3/4

23,000

10

1520

B

AR2-108316

1

36,000

8

2310

B

AR2-101316

1

36,000

10

2895

B

 

Triple Eye

Catalog Number

Rod Diameter

Minimum Strength (Lbs.)

Length (Ft.)

Approximate Weight

(Lbs. per 100 pieces)

Detail

AR3-348316

3/4

23,000

8

1,255

C

AR3-108316

1

36,000

8

2,310

C

AR3-101316

1

36,000

10

2,895

C

AR3-11410316

1 1/4

58,000

10

4,620

C

 

Screw Anchor

06-Poleline-Hardware-image-02

Part

Number

Blade Diameter

Rod Size

Approx. Strength Dry Clay (Lbs.)

Std. Pkg.

Shipping wt. Lbs./100 pieces

SA-3456

6

3/4” x 5’6”

5,000

5

1,050

SA-1056

8

1” x 5’6”

8,000

2

8,000

*Material Stainless Steel Type 316
*Rod equipped with welded sharp stainless steel blades
*Large triple eye to take 1″ bar for hand installation
*Blade pitched to bite correctly into soil without undue earth disturbance
*Chisel point is provided to aid installation

Rock Anchors

Stainless Steel Type 316
(Complete with Rods)

06-Poleline-Hardware-image-03The rock anchor fits into a hole 1-7/8″ or 2-3/8″ and expands and wedges firmly against solid rock. When the anchor is expanded, the greater the pull on the rod, the harder the anchor becomes wedged. No lead, concrete, or grouting equipment is necessary. Furnished complete with 3/4″ and 1″ in rods, 15″ to 8 ft. in length. When ordering galvanized steel parts replace the “6” with a “7” on the catalog number.

Catalog Number

Rod Dia. (Inches)

Rod Length (Inches)

Anchor Size Closed (Inches)

Anchor Size Exposed (Inches)

Hole Size (Inches)

Approx. Weight (Lbs. Each)

RA-3415

3/4

15

1 3/4

2 3/8

1 7/8

5

RA-3430

3/4

30

1 3/4

2 3/8

1 7/8

7

RA-3453

3/4

53

1 3/4

2 3/8

1 7/8

10

RA-3460

3/4

60

1 3/4

2 3/8

1 7/8

11

RA-3472

3/4

72

1 3/4

2 3/8

1 7/8

12

RA-3484

3/4

84

1 3/4

2 3/8

1 7/8

13

RA-3496

3/4

96

1 3/4

2 3/8

1 7/8

15

RA-1015

1

15

2 1/4

3 1/8

2 3/8

10

RA-1030

1

30

2 1/4

3 1/8

2 3/8

14

RA-1053

1

43

2 1/4

3 1/8

2 3/8

18

RA-1072

1

72

2 1/4

3 1/8

2 3/8

24

RA-1084

1

84

2 1/4

3 1/8

2 3/8

26

RA-1096

1

96

2 1/4

3 1/8

2 3/8

29

 

Rock Anchor Extension

06-Poleline-Hardware-image-04

Part

Number

Rod Diameter

Length

Load (Lbs.)

Shipping wt. Lbs./100 Pieces

Std. Pkg.

RAE-583

5/8

3’-0”

12,500

500

10

RAE-343

3/4

3’-0”

18,500

750

10

RAE-344

3/4

4’-0”

18,500

850

5

RAE-345

3/4

5’-0”

18,500

1,000

5

 

*Stainless Steel Type 316
*C.S.A. Standard
*Safety bolts 3/4″ x 4-1/2″ included
* Used where rock formation is near surface
*Drop forged with the clevis swedged to rod
*Double thimble eye for one of two guy strand wires

 

Thimble Eye Nuts (PISA)

06-Poleline-Hardware-image-05

Size (Inches

Part Numbers

Single Eye

Double Eye

Triple Eye

5/8” (5/8” Rod)

TEN58SS

DTEN58SS

TTEN58SS

1” (3/4” & 1” Rod)

TEN100SS

DTEN341SS

TTEN341SS

1 1/4”

TTEN114SS

 

Extension Rods (PISA)

Material: 316 Stainless Steel

06-Poleline-Hardware-image-06

Part Number

Rod Size

Thread

Diameter

Std.

Packaging

Shipping Wgt.

Lbs./100 pieces

Dia.

Length

PER-5870

5/8

7’-0”

5/8

10

750

PER-3470

3/4

7’-0”

1

10

1085

PER-1070

1

7’-0”

1

5

1875

PER-5836

5/8

3’-6”

5/8

10

400

PER-3436

3/4

3’-6”

1

10

585

PER-1036

1

3’-6”

1

5

985

 

 

Anchor Rods

Multi Helix Square Shaft Anchors, Triple Helix

Material: Type 316 & 17-4PH Stainless Steel

06-Poleline-Hardware-image-07

Helixes

Catalog Number

8”, 10”, & 12”

THAT-316SS

Three 10”

THMA-10T-316SS

 

Anchor Shaft Extensions

06-Poleline-Hardware-image-08

Anchor Shaft Extensions

1-1/2” Square with Upset Coupling

And High Strength Bolt

Catalog Number

Length (Feet)

ASE-3.5-316SS

3.5

ASE-50-316SS

5

ASE-70-316SS

7

ASE-100-316SS

10

 

Extension Coupler

06-Poleline-Hardware-image-09

Extension Coupler
Cast 17-4 PH Stainless

Catalog Number (THAEC1-316SS)

 

Guy Attachment

with High Strength Bolt
Material: 316 Stainless Steel

06-Poleline-Hardware-image-10

Catalog Number

Description

GAU-3316SS

Triple Eye With Upset Coupling

 

Note:
Above for 1-1/2″ square and 1-1/4″ round, may be used with single double guys.

 

Guy Attachments

Material: Stainless Steel Type 316 of Silicon Bronze
Angle guy attachments are made of flat stainless steel. The strand bearing surface is rounded to provide protection to the strand without the use of a guy thimble.

06-Poleline-Hardware-image-11

 

Guy Hooks:

Made from half oval steel bent with flat side toward pole, the rounded side prevents injury to the guy strand.

Material: Type 316 Stainless Steel

Catalog Number

Detail Letter

Description

Dimensions (inches)

Approx. Wt.

Lbs./100 Pieces

Bolt Hole

Size

AGA158SS

A

1-Bolt Type

11/16

1/4x2x4 1/8

114

AGA134SS

A

1-Bolt Type

13/16

1/4x2x4 1/8

114

AGA20SS

B

2-Bolt Type

9/16-13/16

1/4x2x7 1/4

150

AJH1SS

C

1-Bolt Type

11/16

3/8x2x4

90

 

Material: Silicon Bronze

Catalog Number

Detail Letter

Description

Dimensions (inches)

Approx. Wt.

Lbs./100 Pieces

Bolt Hole

Size

AGA158SB

A

1-Bolt Type

11/16

1/4x2x4 1/8

114

AGA134SB

A

1-Bolt Type

13/16

1/4x2x4 1/8

114

AGA20SB

B

2-Bolt Type

9/16-13/16

1/4x2x7 1/4

150

AJH1SB

C

1-Bolt Type

11/16

3/8x2x4

90

 

Guy Hook Span Type

For guy attachment use at angles 0 to 30 degrees from horizontal
Material: Stainless Steel Type 316

06-Poleline-Hardware-image-12

Part Number

Max Thru

Bolt Diameter

Max Guy Strand Diameter

Approx. Ship Wgt.

Lbs./100 Pieces

GHST58-T

5/8”

1/2

66

GHST58-T

Tapped 5/8-11

1/2

75

GHST34-T

3/4”

1/2

64

GHST34-T

Tapped ¾-10

1/2

73

 

Ball Clevis

Specifications:
Material: AISI Type 316 Stainless Steel
Clevis pin, bent clevis bolt and nut, AISI Type 316 Stainless Steel
Cotter pin: Stainless Steel

06-Poleline-Hardware-image-13

Number: BC-30M-SS316
Ultimate Breaking Strength: 30,000
Insulator Class: ASA 52 3 & 5
Dimensions: A = 1 15/16
B = 1 9/16
C = 13/16
D = 1 11/16
E = 5/8

Weight (Lbs./C) = 110

 

Socket Eye

Catalog Number: SE-30M-SS316
Specifications:
Material: Body – AISI Stainless Steel Type 316
Cotter Pin: Stainless Steel
Note: Cotter pin included with each socket eye
Ultimate Breaking Strength: 30,000 (Lbs.)
Approx. Weight (Lbs., each): 1.40

06-Poleline-Hardware-image-14

Eye Nut, Weldless

Material: Type 316 Stainless Steel or Type 655 Silicon Bronze
(See chart below for description)

06-Poleline-Hardware-image-15

Catalog Number

Rod Size A

Size Number

WLL Rated Load

Rod Take-Out

Max Pin Dia. C

D

E

G

Weight per 100

316 Type

655 Type

OEN-38SS

OEN-38SB

3/8

1

1250

1 1/2

1 3/16

1/2

2

11/16

63

OEN-12SS

OEN-12SB

1/2

2100

63

OEN-58SS

OEN-58SB

5/8

3600

62

OEN-34SS

OEN-34SB

3/4

5200

60

OEN-78SS

OEN-78SB

7/8

2

7200

2

1 5/8

3/4

2 5/8

1

170

OEN-10SS

OEN-10SB

1

9500

OEN-144SS

OEN-144SB

1/1/4

3

12,480

2 1/2

1 3/4

1

3 3/8

1 1/4

364

OEN-112SS

OEN-112SB

1 1/2

15,400

345

Note: Working load limit for straight line pull only.
Note: Do not exceed working load limit.

 

Shackles

Anchor Shackle

06-Poleline-Hardware-image-16Catalog Number: AS-1.0-SL-SS316
Specifications:
Material: AISI Type 316 Stainless Steel
Clevis Pin: AISI Type 316 Stainless Steel
Ultimate Breaking Strength: 60,000 Lbs.
Dimensions in inches A = 3 1/2
B = 3/4
C = 1 1/4
E = 3/4
F = 1 7/8
G = 1
Weight (Lbs./C) = 242

 

Screw Pin, Safety Pin

Specifications:
Material: Type 316 Stainless Steel
Note: Larger sizes, chain shackles, other pin styles
and stainless grades can be furnished on special order.

06-Poleline-Hardware-image-17

Size “A”

Catalog Number

Dimensions (Inches)

Screw Pin

Safety Pin

“B”

“C”

“D”

“E”

“F”

1/4

SPAS140

SPNAS140

5/16

1 1/8

1/2

3/4

11/16

5/16

SPAS516

SPNAS516

3/8

1 1/4

17/32

27/32

3/4

3/8

SPAS380

SPNAS380

7/16

1 7/16

21/32

31/32

15/16

7/16

SPAS716

SPNAS716

1/2

1 3/4

23/32

1 5/32

1 1/8

1/2

SPAS120

SPNAS120

5/8

1 15/16

13/16

1 1/4

1 1/4

5/8

SPAS580

SPNAS580

3/4

2 7/16

1 1/16

1 9/16

1 7/16

3/4

SPAS340

SPNAS340

7/8

3

1 1/4

1 7/8

1 7/8

7/8

SPAS780

SPNAS780

1

3 1/4

1 7/16

2 1/8

2

1

SPAS100

SPNAS100

1 1/8

3 3/4

1 11/16

2 1/2

2 3/8

 

Size “A”

Catalog Number

Tolerance +/-

(Inches)

Weight

Each (Lbs.)

Working Load

Limit (Lbs/kg)

Screw Pin

Safety Pin

Length

Width

1/4

SPAS140

SPNAS140

1/16

1/16

.10

450/204

5/16

SPAS516

SPNAS516

1/16

1/16

.16

650/295

3/8

SPAS380

SPNAS380

1/8

1/16

.20

1000/454

7/16

SPAS716

SPNAS716

1/8

1/16

.50

1375/624

1/2

SPAS120

SPNAS120

1/8

1/16

.72

1990/903

5/8

SPAS580

SPNAS580

1/8

1/16

1.38

3000/1383

3/4

SPAS340

SPNAS340

1/4

1/16

2.22

4475/2030

7/8

SPAS780

SPNAS780

1/4

1/16

3.28

6000/2722

1

SPAS100

SPNAS100

1/4

1/16

5.31

7950/3606

 

Guy Hook

Material Specifications: Stainless Steel Type 316

06-Poleline-Hardware-image-18

Catalog Number

Maximum Wire

Mounting

Bolts

Dimensions (Inches)

Minimum Ultimate (Lbs.)

“A”

“B”

“C”

“R”

GH1-316SS

9/16

5/8 – 3/4

3

5/16

2 7/8

3/4

20,000

GH2-316SS

3/4

Top 1 – 7/8

Bottom 3/4 – 5/8

And/or 1/2 LS

4

1

3 7/16

7/8

25,000

*Two spurs to resist pole splitting
*More surface in contact with pole than other comparable guy attachments – greater protection to wood fibers
*For round or flat surfaces
*Will intercept wire at any angle

 

Support Clamp, Messenger

Material: Galvanized Steel
Catalog Number: MSC1-GA, MSC2-SS-Stainless Steel
Equivalent To: Joslyn PA178
Mounting Bolt: 5/8″
Messenger Range: 0.35 – 0.75 Diameter
Pole to Messenger: 1 1/2″

06-Poleline-Hardware-image-19

*Hanger exceeds medium duty requirements EE1-NEMA standards for aerial cable hangers.
*Has a hook to support cable during stringing operation.
*independent clamping ensures that the messenger remains secured if pole shrinkage occurs.
*Curved grooved saddle for additional cable support.
*The bottom lip groove move to an upward position to support cable during installation.

 

Suspension Clamps, Messenger

Material: AISI Type 316 Stainless Steel
Specification sheets on following pages.

06-Poleline-Hardware-image-20

Note: All hardware for above items are included:

Catalog Number

Description

Dimension (Inches)

Approx. Weight

(Lbs.)/100 Pieces

Strand Size

Length

Mtg. Hole

SBSC1-316SS

1-Bolt Straight

1/4 – 7/16

2 3/8

11/16

76

TBC1-316SS

3-Bolt Straight

1/4 – 7/16

5 3/4

11/16

224

TBC1.5-316SS

3-Bolt Straight

1/4 – 7/16

5 3/4

13/16

224

TBC2-316SS

3-Bolt Straight

3/8 – 3/4

5 3/4

13/16

224

TBCC1-316SS

3-Bolt Curved

1/4 – 7/16

7 1/4

11/16

290

TBCC1.5-316SS

3-Bolt Curved

1/4 – 7/16

7 1/4

13/16

375

*Heavy Duty

 

Messenger Clamp, Serpentine

06-Poleline-Hardware-image-21

Serpentine clamp for jacketed strand
Figure 8 messenger

The illustration above details the use of a cable clamp. The clamp has serpentine grooves to prevent slippage of jacket strand through the clamp. This clamp may be used on all straight line poles and at the corner with angles up to 30 degrees. The clamp is installed without slitting the web.

06-Poleline-Hardware-image-22

Standard Pole Attachment Detail

Catalog Number

Description

Dimension (Inches)

Approx. Weight

(Lbs.)/100 Pieces

Strand Size

Length

Mtg. Hole

SBSC1-316SS

1-Bolt Straight

1/4 – 7/16

2 3/8

11/16

76

TBC1-316SS

3-Bolt Straight

1/4 – 7/16

5 3/4

11/16

224

TBC1.5-316SS

3-Bolt Straight

1/4 – 7/16

5 3/4

13/16

224

TBC2-316SS

3-Bolt Straight

3/8 – 3/4

5 3/4

13/16

224

TBCC1-316SS

3-Bolt Curved

1/4 – 7/16

7 1/4

11/16

290

TBCC1.5-316SS

3-Bolt Curved

1/4 – 7/16

7 1/4

13/16

375

 

Lashing Wire Clamp

Material: Stainless Steel Type 304
Catalog Number: LWC-304SS

Material: CDA-655 Silicon Bronze
Catalog Number: LWC-655SB

06-Poleline-Hardware-image-23

Not: Studs are staked to prevent nuts from coming off during packing or shipment.

Stainless Steel & Silicon Bronze Lashing Wire Clamp Specifications

1. Scope:
This item standard is intended for use in conjunction with CSA standard CAN/CSA-C83. This item is normally mounted on messenger strand and is used to terminate cable lashing wire.

2. Assembly:
The lashing wire clamp is comprised of two clamp sections, two flat washers, and two hex nut assemblies on a shouldered stud. The stud should key into one clamp section at assembly to prevent stud rotation as the nuts are tightened. This keying feature is constructed to allow proper closing of the jaws. Both ends of the stud should be suitably modified after assembly to prevent loss of the nuts.

3. Accommodation:
The clamp will accommodate a range of messenger strand from 3/16″ to 9’16” diameter designated strand size.

4. Stud Strength:
The stud will withstand without fracture a torque of 10 N*m and 15 N*m for minimum reusable and ultimate torque strength.

5. Slip Strength Test:
The clamp shall be assembled to a suitably anchored length of strand of designated strand size No. 5, CSA Standard CAN3-G12, and the clamp nut is tightened to 10 N*m torque. A force of 1 kn, applied to the clamp, parallel to the strand, will cause less than 4mm movement between the clamp and strand.

 

Wire Rope Clips

Stainless Steel Type 316 (Drop Forged)

06-Poleline-Hardware-image-24

Catalog Number

Size

Minimum Number of Clips Required

Torque in Lbs. Ft.

Approx. Wgt. Each (Lbs.)

Amount of rope to turn back

WRC-180

1/8

2

4.5

.05

3 1/4

WRC-316

3/16

2

7.5

.106

3 3/4

WRC-140

1/4

2

15

.19

4 3/4

WRC-380

3/8

2

45

.46

6 1/2

WRC-120

1/2

3

65

.68

11 1/2

WRC-580

5/8

3

95

1.0

12

*Based on clean, unlubricated threads.
Minimum torque required to reach max. holding power.

06-Poleline-Hardware-image-25

Below is the recommended method of applying U-bolt clips to get maximum holding power of the clip and is based on the use of proper size U-bolts on new rope.

1. Refer to above table in following these instructions. Turn back specified amount of rope from thimble or loop. Apply first clip, one base width from dead end of rope. Apply U-bolt over dead end of wire rope with live end resting in saddle. Tighten nuts evenly, alternating from one nut to the other until reaching the recommended torque.

2. When two clips are required apply the second clip as near the loop or thimble as possible. Tighten nuts evenly, alternating until reaching the recommended torque. When more than two clips are required, apply the second clip as near the loop or thimble as possible, turn nuts on second clip firmly, but do not tighten. Proceed to step 3.

3. When three or more clips are required, space additional clips evenly between first two, take up rope, slack-tighten nuts on each U-bolt evenly, alternating from one nut to the other until reaching recommended torque.

4. Apply first load to test the assembly. This load should be of equal or greater weight than loads expected in use. Next, check and re-tighten nuts to recommended torque.

(Reprinted from the Wire Rope Users Manual and the Wire Rope Technical Board)

 

Wire Rope Thimbles

Standard Wire Rope Thimbles
Material: Stainless Steel Type 302

06-Poleline-Hardware-image-26

Dimensions (Inches)

Catalog Number

Rope Diameter

Overall Thickness

Overall Length

Inside Width

Weight Per 100 Lbs.

SWRT180

1/8

9/32

1 3/4

23/32

3

SWRT316

3/16

11/32

1 3/4

23/32

3

SWRT140

1/4

3/8

1 7/8

23/32

5

SWRT516

5/16

7/16

2 3/32

27/32

5

SWRT380

3/8

9/16

2 1/4

31/32

8

SWRT120

1/2

21/32

2 1/2

1 5/32

14

Note: Thimbles are not designed for load carrying purposes, therefore working load limits have not been established.

Heavy Wire Rope Thimbles

Material: Stainless Steel Type 316

06-Poleline-Hardware-image-27

Dimensions (Inches)

Catalog Number

Rope Diameter

Overall Thickness

Overall Length

Inside Width

Weight Per 100 Lbs.

HWRT140

1/4

3/32

2 316

7/8

7.5

HWRT516

5/16

1/2

2 1/2

1 1/16

14

HWRT380

3/8

21/32

2 7/8

1 1/8

25

HWRT120

1/2

27/32

3 5/8

1 1/2

51

HWRT580

5/8

1

4 1/4

1 3/4

75

HWRT340

3/4

1 1/4

5

2

147

 

Thimble Eye Nut

Material: Stainless Steel Type 316 & Bronze

06-Poleline-Hardware-image-28

Catalog Number

Bolt Diameter

Dimensions (Inches)

“A”

“B”

“C”

“D”

`”E”

“F”

TEN58SS

5/8

1 1/2

1 1/2

7/8

1 3/8

1 7/8

3

TEN34SS

3/4

1 1/2

1 1/2

7/8

1 3/8

1 7/8

3

TEN58SB

5/8

1 1/2

1 1/2

7/8

1 3/8

1 7/8

3

TEN34SB

3/4

1 1/2

1 1/2

7/8

1 3/8

1 7/8

3

 

Crossover Clamps

Stainless Steel Type 316
Crossover Clamps for CATV or Telephone Cables

06-Poleline-Hardware-image-29

Crossover clamps are used to clamp two messengers where they cross at right angles. The drop forged clamp sections are 1-1/2″ wide and 3-1/4″ long. Two 1/2″ diameter bolts have oval shoulders to prevent turning when tightening. Unique cable grooves with a center “dimple” provide superior clamping action.

Part Number

For Strand Diameter (Inches)

Approximate Shipping Weight (Lbs. per 100 Pcs.)

COCI-316SS

5/16 to 3/8

154

 

Span Clamp

Material: Stainless Steel Type 316
Catalog Number: SPC1-316SS

06-Poleline-Hardware-image-30

 

Copper Ground Wire Clips

06-Poleline-Hardware-image-31

Part

Number

“A”

(Inches)

“B”

(Inches)

“C”

(Inches)

“D”

(Inches)

“R”

(Inches)

CGWC-1

1 1/2

3/4

1/8

9/32

3/16

*Made from Hard Copper Flat bar.
*Used for clamping stranded wire.
*Made to Hydro Spec.

 

Ground Wire Clips

06-Poleline-Hardware-image-32

*Made from 1/8″ x 3/4″ Stainless Steel Type 316
*Used to fasten ground wires on steel structures.
*Accommodates conductor range of 1/0 to 2000 MCM AWG Stranded Copper

 

Angle Thimble Eyelet

06-Poleline-Hardware-image-33

Part Number

Bolt Dia. (Inches)

Strand Diameter

Strength (Lbs.)

Wt. Lbs. Per 100 Pcs.

Std. Pack

ATE1-316SS

5/8

3/16 to 1/2

12,400

138

50

AET2-316SS

3/4

3/16 to 1/2

18,300

128

50

*Drop Forged Stainless Steel Type 316.
*At 45 degree angle.

 

Bolt Eyes

06-Poleline-Hardware-image-34

Part Number

Bolt Dia. (Inches)

Bolt Hole (Inches)

Inside Eye (Inches)

Wt. Lbs. Per 100 Pcs.

Std. Pack

BE1-316SS

5/8

13/16 x 1

1 1/4 x 3

125

50

BE2-316SS

3/4

11/16 to 1

1 1/4 x 3

125

50

*Drop Forged Stainless Steel Type 316.
*Bolt can be inserted at any angle because hole is elongated.
*Used for Dead-Ending on cross arms.

 

Thimble Eye Bolts, Straight

06-Poleline-Hardware-image-35

5/8″ Diameter
Minimum Strength 12,400 Lbs

Part Number

Length (Inches)

Approx. Wgt.

(Lbs. per 100 Pcs.)

STEB5808

8

125

STEB5810

10

144

STEB5812

12

162

STEB5814

14

180

STEB5816

16

195

STEB5818

18

216

STEB5820

20

236

 

3/4″ Diameter
Minimum Strength 18,300 Lbs

Part Number

Length (Inches)

Approx. Wgt.

(Lbs. per 100 Pcs.)

STEB3410

10

210

STEB3412

12

235

STEB3414

14

260

STEB3416

16

285

STEB3418

18

310

STEB3420

20

330

*Drop Forged Stainless Steel Type 316
*Threads are 6″ long.
*Each bolt supplied with one square nut.

 

Thimble Eye Bolts, Angle

06-Poleline-Hardware-image-36

5/8″ Diameter
Minimum Strength 12,400 Lbs.

Part Number

Length (Inches)

Approx. Wgt.

(Lbs. per 100 Pcs.)

ATEB5808

8

130

ATEB5810

10

148

ATEB3414

12

166

ATEB3416

14

184

ATEB3418

16

202

ATEB3420

18

220

ATEB5820

20

238

 

3/4″ Diameter
Minimum Strength 18,300 Lbs.

Part Number

Length (Inches)

Approx. Wgt.

(Lbs. per 100 Pcs.)

ATEB3410

10

200

ATEB3412

12

225

ATEB3414

14

250

ATEB3416

16

275

ATEB3418

18

300

ATEB3420

20

310

*Drop Forged Stainless Steel Type 316
*Minimal length of threads is 6″.
*Each bolt supplied with one square nut.
*Bent at an angle of 45 degrees.

 

Guy Clamp

*Parallel grooves trap strand tightly without marring.
*Plate halves align evenly for easy application. Each bolt has a shoulder to prevent turning while tightening.
*Material: Stainless Steel Type 316

06-Poleline-Hardware-image-37

5/8″ Clamp Bolts

Part Number

Number of Bolts

Length (Inches)

Width (Inches)

Accepts Strand Size

Ship Wgt. Lbs. per 100 Pcs.

GC1-316SS

3

6

1 21/32

5/16 thru 1/2

252

 

Hub Guards, Pole Shields

06-Poleline-Hardware-image-38

Part Number

Dimensions (Inches)

Radius (Inches)

HG-PS1-316SS

3/16x16x18

7 1/2

HG-PS2-316SS

3/16x16x30

7 1/2

HG-PS3-316SS

3/16x14x30

5 1/2

*Used to protect poles from vehicle collision.
*Holes are 9/16″ for 1/2″ lag bolts.

Guy Strain Plates

06-Poleline-Hardware-image-39

Part Number

Detail

Size

Wgt. Lbs. per 100 Pcs.

SP1-316SS

“A”

4x8x12Ga.

110

SP2-316SS

“B”

4x8x12Ga.

146

 

Rod Coupling, Threaded

06-Poleline-Hardware-image-40

Part Number

Rod Diameter

Length (Inches)

316

Bronze

RC-T58SS

RC-T58SB

5/8

3

RC-T10SS

RC-T10SB

1

3

 

Anchor Rod Extensions

Material: Stainless Steel Type 316 and Bronze

06-Poleline-Hardware-image-41

Part Number

Rod Diameter

Length (Inches)

316

Bronze

ARE5835SS

ARE5835SB

5/8

3.5

ARE588SS

ARE588SB

5/8

8

ARE1035SS

ARE1035SB

1

3.5

ARE1010SS

ARE1010SB

1

10

 

Cross Plate Anchors

Material: Stainless Steel Type 316 Plate
(Nut Retainer Welded to plate)

06-Poleline-Hardware-image-42

Part Number

Size (Inches)

Rod Size

CPA-16

16

5/8

CPA-24

24

1

 

Cable Messenger Hanger

P/N CMH-1070SS
Material: Stainless Steel Type 316

P/N CMH-1070SB
Material: CDA-655 Silicon Bronze

06-Poleline-Hardware-image-43

Lift and Load, Plates

Used to protect poles on heavy down guying when thimble eye, angle thimble eye, or oval bolts are used through the pole.
Material: Stainless Steel Type 316

06-Poleline-Hardware-image-44

Catalog Number

Description

Size of Holes (Inches)

Plate Size (Inches)

Approx. Ship Wgt. (Lbs. per 100 pieces)

Top

Bottom

LP2H1

2-Hole Lift

9/16

3/4×1

3/16×2 1/2×7

98

LP2H2

2-Hole Lift

9/16

7/8×1

1/4×2 1/2×7

126

LP3H1

3-Hole Lift

9/16

3/4×1

3/16×2 1/2×7

97

LP3H2

3-Hole Lift

9/16

7/8×1

1/4×2 1/2×7

126

 

Turnbuckles, Open Body

Material: Drop Forged from Type 316 Stainless Steel

06-Poleline-Hardware-image-45

Catalog Numbers & Working Load Limits

Diameter (Inches)

Take-up (Inches)

Catalog Numbers

Working Load Limit (Lbs.)

With Stubs

Eye & Eye

Jaw & Eye

Jaw & Jaw

1/4

4

T-OBSE140

T-OBEE140

T-OBJE140

T-OBJJ140

460

5/16

4 1/2

T-OBSE516

T-OBEE516

T-OBJE516

T-OBJJ516

780

3/8

6

T-OBSE380

T-OBEE380

T-OBJE380

T-OBJJ380

1160

1/2

6

T-BOSE120

T-OBEE120

T-OBJE120

T-OBJJ120

2150

5/8

6

T-OBSE580

T-OBEE580

T-OBJE580

T-OBJJ580

3440

3/4

6

T-OBSE340

T-OBEE340

T-OBJE340

T-OBJJ340

5140

7/8

6

T-OBSE780

T-OBEE780

T-OBJE780

T-OBJJ780

7130

1

6

T-OBSE100

T-OBEE100

T-OBJE100

T-OBJJ100

9370

 WARNING: DO NOT EXCEED WORKING LOAD LIMIT

Dimensions & Weights

Diameter (Inches)

Overall Length (Inches) (Bearing to Bearing Closed)

Weight Each (Pounds)

Body Only

With Stubs

Eye & Eye

Jaw & Eye

Jaw & Jaw

With Stubs

Eye & Eye

Jaw & Eye

Jaw & Jaw

1/4

4 3/4

9

**7

**7 1/4

7 1/2

.25

.25

.30

.34

5/16

5 7/16

10 1/2

**8

**8

8 1/4

.34

.34

.40

.44

3/8

7 1/8

15

11 1/4

11 1/4

10 7/8

.75

.77

.84

.94

1/2

7 1/2

15

14

13

12 1/2

1.25

1.5

1.58

1.65

5/8

7 7/8

16

14 3/4

14 7/8

14

2.00

2.35

2.75

3.09

3/4

8 1/4

17

17 1/4

16 1/4

14 7/8

3.19

3.99

4.29

4.56

7/8

8 5/8

17

18

16 1/4

14 1/4

6.00

6.16

6.28

6.48

1

.9

18

19 1/4

18 3/4

17 1/2

6.375

8.73

9.22

9.66

**Round Eye Style

 

Turnbuckles, Closed Body

with Electroline “FIEGE” rope socket

Machined Series: Closed Body Clevis and Socket Turnbuckles

06-Poleline-Hardware-image-46

Catalog Number

Dimensions (inches)

Rope Size

Self-Colored Steel

Zinc Plated Steel

Stainless Steel

A

B

C Min

D

E

F

Takeup (Inches)

1/16

ID-406

ID-406

IS-406

17/64

3/8

6-5/16

7/16

3/16

3/16

2-1/2

3/32

ID-409

ID-409

IS-409

5/16

1/2

7-11/16

9/16

1/4

1/4

2-7/8

1/8

ID-412

ID-412

IS-412

5/16

1/2

7-11/16

9/16

1/4

1/4

2-7/8

5/32

ID-415

ID-415

IS-415

3/8

5/8

9-1/2

11/16

5/16

5/16

3-1/8

3/16

ID-418

ID-418

IS-418

3/8

5/8

9-1/2

11/16

5/16

5/16

3-1/8

7/32

ID-421

ID-418

IS-418

15/32

3/4

10-15/16

7/8

3/8

3/8

4-13/16

1/4

ID-425

ID-425

IS-425

15/32

3/4

10-15/16

7/8

3/8

3/8

4-13/16

9/32

ID-428

ID-428

IS-428

17/32

7/8

11-11/16

1

3/8

7/16

4-9/16

5/16

ID-431

ID-431

IS-431

17/32

7/8

11-11/16

1

3/8

7/16

4-9/16

3/8

ID-437

ID-437

IS-437

5/8

1

13-1/4

1-1/8

7/16

1/2

5-5/16

7/16

ID-443

ID-443

IS-443

23/32

1-1/4

17-7/32

1-5/16

7/16

5/8

8-1/16

1/2

ID-450

ID-450

IS-450

51/64

1-3/8

17-3/4

1-1/2

1/2

11/16

8-1/16

Note: A swaged turnbuckle body may be substituted for smaller rope sizes, resulting in an overall length slightly longer than indicated.

Machined Series: Closed Body Double Socket Turnbuckles

06-Poleline-Hardware-image-47

Catalog Number

Dimensions  (Inches)

Rope Size

Self Colored Steel

Zinc Plated Steel

Stainless Steel

C Min

D

Take-up (Inches)

1/16

ID-5506-N

ID-5506-V

IS-5506

6-3/8

7/16

2-1/2

3/32

ID-5509-N

ID-5509-V

IS-5509

7-1/4

9/16

2-7/8

1/8

ID-5512-N

ID-5512-N

IS-5512

7-1/4

9/16

2-7/8

5/32

ID-5515-N

ID-5515-V

IS-5515

8-5/8

11/16

3-1/8

3/16

ID-5518-N

ID-5518-V

IS-5518

8-5/8

11/16

3-1/8

/32

ID-5521-N

ID-5521-V

IS-5521

11-7/8

7/8

4-13/16

1/4

ID-5525-N

ID-5525-V

IS-5525

11-7/8

7/8

4-13/16

9/32

ID-5528-N

ID-5528-V

IS-5528

12-7/8

1

4-9/16

5/16

ID-5531-N

ID-5531-V

IS-5531

12-7/8

1

4-9/16

3/8

ID-5537-N

ID-5537-V

IS-553

14-1/2

1-1/8

5-5/16

7/16

ID-5543-N

ID-5543-V

IS-5543

18-5/8

1-5/16

8-1/16

1/2

ID-5550-N

ID-5550-V

IS-5550

19-1/4

1-1/2

8-1/16

Note: A swaged turnbuckle body may be substituted for smaller rope sizes, resulting in a slightly longer overall length.

Machined Series: Closed Body Double Clevis Turnbuckle

06-Poleline-Hardware-image-48

Catalog Number

Dimensions (inches)

Rope Size

Self-Colored Steel

Zinc Plated Steel

Stainless Steel

A

B

C Min

D

E

F

Takeup (Inches)

1/16

IjD-406-N

IJD-406-V

IJS-406

17/64

3/8

5-5/32

21/32

3/16

3/16

2-1/2

3/32

IJD-409-N

IJD-409-V

IJS-409

5/16

1/2

6-1/4

13/16

1/4

1/4

2-7/8

1/8

IJD-412-N

IJD-412-V

IJS-412

5/16

1/2

6-1/4

13/16

1/4

1/4

2-7/8

5/32

IJD-415-N

IJD-415-V

IJS-415

3/8

5/8

7-5/16

15/16

5/16

5/16

3-1/8

3/16

IJD-418-N

IJD-418-V

IJS-418

3/8

5/8

7-5/16

15/16

5/16

5/16

3-1/8

7/32

IJD-421-N

IJD-418-V

IJS-418

15/32

3/4

10

1-1/8

3/8

3/8

4-13/16

1/4

IJD-425-N

IJD-425-V

IJS-425

15/32

3/4

10

1-1/8

3/8

3/8

4-13/16

9/32

IJD-428-N

IJD-428-V

IJS-428

17/32

7/8

10-1/2

1-5/16

3/8

7/16

4-9/16

5/16

IJD-431-N

IJD-431-V

IJS-431

17/32

7/8

10-1/2

1-5/16

3/8

7/16

4-9/16

3/8

IJD-437-N

IJD-437-V

IJS-437

5/8

1

12

1-7/16

1/2

1/2

5-5/16

7/16

IJD-443-N

IJD-443-V

IJS-443

23/32

1-1/4

15-13/16

1-5/8

7/16

5/8

8-1/16

1/2

IJD-450-N

IJD-450-V

IJS-450

51/64

1-3/8

16-7/32

1-5/8

1/2

11/16

8-1/16

Note: A swaged turnbuckle body may be substituted for smaller rope sizes, resulting in a slightly longer overall length.

 

Ball Bearing Swivels, Gold Band Angular Contact

06-Poleline-Hardware-image-49

Streamlined design and maximum performance
*Designed for high rotational speeds, these models react to low operational torque…the perfect swivels for longer ropes & cables.
*Manufactured with two or more flush ground angular contact ball bearings.
*Bearings are permanently lubricated with high-pressure grease and sealed at the factory.
*Flush pins are available for overhead and underground electrical line stringing (please specify). Swivel ends are shaped to prevent snagging when gliding over sheaves and other potential obstructions.
*Heat-treated high strength alloy steel, zinc plated for corrosion resistance, provides the strongest yet lightest swivel available. Ultimate strength is minimum 4.5 to 1 over SWL (Safe Working Load).
*All swivels proof tested and certified.

6000 Series Gold Band Swivels

Size

SWL Tons

Wire Rope Size

A

C Pin Dia.

D

E

F

G

H

I

J Hole Dia.

K

12

.5

(.9)

1/8

7/8

5/16

5/16

1/4

15/32

7/8

3/8

3/8

1/4

3/8

25

.75

(2)

1/4

1-1/4

3/8

19/32

5/16

11/16

31/321

1/2

7/16

3/8

7/16

37

1.5

(4)

3/8

1-1/2

7/16

19/32

1/2

13/16

1

23/32

9/16

5/8

5/8

50

3

(5)

1/2

1-7/8

5/8

3/4

3/4

15/16

1-11/32

05/16

13/16

7/8

15/16

62

5

(8)

5/8

2-7/16

7/8

1

1

1-9/16

1-11/16

1-5/16

1-1/8

1-1/4

1-3/16

75

8.5

(15)

3/4

2-7/8

1

1-9/32

1-1/4

2-1/8

2-1/4

1-5/8

1-1/4

1-3/8

1-1/2

81

8.5

(15)

3/4

2-7/8

1-1/8

1-9/16

1-1/4

2-1/8

2-1/4

1-5/8

1-1/4

1-3/8

1-1/2

87

10

(17)

7/8

3-5/8

1-1/2

1-3/4

1-23/32

3-1/2

3

2-27/32

1-3/4

1-5/8

1-13/16

99

15

(20)

1

3-5/8

1-1/2

1-3/4

2

3-1/2

3

2-25/32

1-3/4

2

2-1/8

150

35

1-1/2

5-3/8

2

2

2-1/4

3-11/16

3-3/4

3-1/8

2-3/8

2-1/4

2-3/8

 

All dimensions are in inches.
Specifications could change without notice.
() For line stringing applications requiring a 3 to 1 Safe Working Load.

Ball Bearing Swivels, Gold Band Angular Contact

6000 Series Gold Band Swivels (Overall Length)

Model

60

61

62

63

67

65/68

66

67

Size

*

*

*

 

 

 

 

 

12

5-5/16

5-3/8

5-3/8

3-7/8

3-7/8

3-1/8

3-1/8

3-1/16

25

8-5/16

7-1/16

7-1/8

5-7/8

5-7/8

4-9/16

4-9/16

4-1/2

37

9-1/2

7-7/8

7-13/16

6-13/16

6-13/16

5-1/8

5-1/8

5-1/8

50

12-15/16

10-13/16

10-15/16

9-1/8

9-1/8

7-1/8

7-1/8

7-1/8

62

17-9/16

15-1/4

15-1/4

12-13/16

12-13/16

10-1/2

10-1/2

10-1/2

75

21-1/8

18-7/8

18-7/8

14-11/16

14-11/16

12-7/16

12-7/16

12-7/16

81

21-1/8

18-7/8

18-7/8

14-11/16

14-11/16

12-7/16

12-7/16

12-7/16

87

25-15/16

24-15/16

24-15/16

18

18

17

17

17

99

27-13/16

25-11/16

25-11/16

19-7/8

19-7/8

17-3/4

17-3/4

17-3/4

150

44-1/16

34-5/8

34-5/8

30-7/8

30-7/8

22-3/8

21-7/16

21/7/16

 

*T inside of hook
All dimensions are in inches.
Specifications could change without notice.

Rope Thimble Swivels

T06-Poleline-Hardware-image-50he best method of attaching a wire or synthetic rope to a swivel is with our FIEGE fitting available on models 60, 63, and 64. If you prefer to use a thimble with clips, we recommend solid core thimbles shown here. These cast steel thimbles are zinc plated and designed to limit rope wear by preventing the rope from extending beyond the diameter of the swivel.

Rope Size

Thimble #

1/2

L713-4

5/8

L713-5

3/4

L713-9

7/8

L713-8

1

L713-8

 

Comments are closed.